[Ocfs2-users] Subject: problem configuring ocfs on rhel5.8 kernel 2.6.18-300.el5

[Asanka Gunasekera]

Hi Tiger, out of my frustration I have made mistakes in the config file, how this is working :)

Thank you and best regards
Asanka


________________________________
 From: Tiger Yang <tiger.yang at oracle.com>
To: Asanka Gunasekera <asanka_gunasekera at yahoo.co.uk> 
Cc: "ocfs2-users at oss.oracle.com" <ocfs2-users at oss.oracle.com> 
Sent: Thursday, 13 September 2012, 8:36
Subject: Re: [Ocfs2-users] Subject: problem configuring ocfs on rhel5.8 kernel 2.6.18-300.el5
 

What is the version of the ocfs2-tools? 

run mkfs.ocfs2 --version to get the tools version.

For 1.4.10, you need ocfs2-tools 1.6.3-2.

Tiger


On 09/12/2012 03:32 PM, Asanka Gunasekera wrote: 
Hi this is a resend from a subscribed address sorry if I am causing any inconvenience
>
>
>
>hope some one can help me on this, I have been straggling to get this working for few weeks now. My issue is as below
>
>I am just trying to use ocfs2 as shared file system between 2
          node HA cluster for a application that runs on these nodes
>
>I have downloaded below packages
>
>ocfs2-2.6.18-238.9.1.el5-1.4.9-1.el5.x86_64.r
>and 
>ocfs2-2.6.18-308.1.1.el5-1.4.10-1.el5.x86_64
>
>Installation goes with out any complains but when its time to
          configure I get below errors
>
>[root at ccbsn01 ~]# /etc/init.d/o2cb configure
>Configuring the O2CB driver.
>
>This will configure the on-boot properties of the O2CB
            driver.
>The following questions will determine whether the driver is
            loaded on
>boot. The current values will be shown in brackets ('[]').
            Hitting
><ENTER> without typing an answer will keep that
            current value. Ctrl-C
>will abort.
>
>Load O2CB driver on boot (y/n) [y]:
>Cluster stack backing O2CB [o2cb]:
>Cluster to start on boot (Enter "none" to clear) [ocfs2]:
>Specify heartbeat dead threshold (>=7) [31]:
>Specify network idle timeout in ms (>=5000) [30000]:
>Specify network keepalive delay in ms (>=1000) [2000]:
>Specify network reconnect delay in ms (>=2000) [2000]:
>Writing O2CB configuration: OK
>Loading filesystem "ocfs2_dlmfs": Unable to load filesystem
            "ocfs2_dlmfs"
>Failed
>
>And in the /var/log/message log I get below error
>
>Sep 12 11:21:41 node01 modprobe: FATAL: Module ocfs2_stackglue not found.
>Sep 12 11:21:41 node01 modprobe: FATAL: Module ocfs2_dlmfs
            not found.
>Sep 12 11:33:13 node01 modprobe: FATAL: Module
            ocfs2_stackglue not found.
>Sep 12 11:33:13 node01 modprobe: FATAL: Module ocfs2_dlmfs
            not found.
>
>How can I fix this and get this working
>
>Thanks and Best Regards
>
_______________________________________________
Ocfs2-users mailing list Ocfs2-users at oss.oracle.com https://oss.oracle.com/mailman/listinfo/ocfs2-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://oss.oracle.com/pipermail/ocfs2-users/attachments/20120913/f53a6df4/attachment-0001.html