========== hostname -s: ========== ca-ostest293 ========== domainname: ========== us.oracle.com ========== uname -a: ========== Linux ca-ostest293.us.oracle.com 2.6.25 #5 SMP Tue Jul 8 08:38:26 PDT 2008 x86_64 x86_64 x86_64 GNU/Linux ========== df -Th: ========== Filesystem Type Size Used Avail Use% Mounted on /dev/cciss/c0d0p3 ext3 49G 37G 9.6G 80% / /dev/cciss/c0d0p1 ext3 251M 150M 89M 63% /boot tmpfs tmpfs 4.0G 4.1M 4.0G 1% /dev/shm /dev/cciss/c0d1p1 ext3 48G 30G 16G 66% /home /dev/cciss/c0d1p2 ext3 87G 24G 59G 29% /opt /dev/sda1 ext3 470G 76G 371G 17% /olt-storage ca-ostest292:/cruc/packages nfs 49G 33G 14G 72% /cruc/packages ca-ostest292:/cruc/plans nfs 49G 33G 14G 72% /cruc/plans ca-ostest292:/cruc/runs nfs 49G 33G 14G 72% /cruc/runs ca-ostest292:/cruc/suts nfs 49G 33G 14G 72% /cruc/suts ca-ostest292:/cruc/usr nfs 49G 33G 14G 72% /cruc/usr ca-ostest292:/cruc/etc nfs 49G 33G 14G 72% /cruc/etc ca-ostest292:/cruc nfs 49G 33G 14G 72% /cruc ========== mount: ========== /dev/cciss/c0d0p3 on / type ext3 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/cciss/c0d0p1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) /dev/cciss/c0d1p1 on /home type ext3 (rw,noatime,data=writeback) /dev/cciss/c0d1p2 on /opt type ext3 (rw,noatime,data=writeback) /dev/sda1 on /olt-storage type ext3 (rw,noatime,data=writeback) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) ca-ostest292:/cruc/packages on /cruc/packages type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc/plans on /cruc/plans type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc/runs on /cruc/runs type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc/suts on /cruc/suts type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc/usr on /cruc/usr type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc/etc on /cruc/etc type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) ca-ostest292:/cruc on /cruc type nfs (rw,bg,nfsvers=3,tcp,hard,intr,addr=139.185.50.76) hugetlbfs on /mnt/hugetlbfs type hugetlbfs (rw) ========== lsmod: ========== Module Size Used by ocfs2_dlm 171676 0 ocfs2_nodemanager 194760 1 ocfs2_dlm hp_ilo 33148 0 parport_pc 27560 0 lp 12612 0 parport 37296 2 parport_pc,lp bnx2 169864 0 tg3 109828 0 lpfc 238324 1 cciss 35336 7 ehci_hcd 32396 0 ohci_hcd 21892 0 uhci_hcd 22560 0 ========== lshw: ========== /cruc/usr/bin/sut_sysinfo: line 11: lshw: command not found ========== lspci -vvv: ========== 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a4) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4149 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 3 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 8, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4151 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 2 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 4, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4159 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 1 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 2, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4161 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 1, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=02:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- 03:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (rev 12) Subsystem: Hewlett-Packard Company NC373i Integrated Multifunction Gigabit Server Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <64ns, L1 <1us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=04:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet (rev 12) Subsystem: Hewlett-Packard Company NC373i Integrated Multifunction Gigabit Server Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <4us, L1 <16us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=06:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 07:04.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5715S Gigabit Ethernet (rev a3) Subsystem: Hewlett-Packard Company NC326i PCIe Dual Port Gigabit Server Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4169 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 2 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 4, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 40:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4171 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 1 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x8 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 2, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 40:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4179 Capabilities: [58] HyperTransport: MSI Mapping Capabilities: [80] Express Root Port (Slot+) IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <512ns, L1 <4us Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0 Link: Latency L0s <512ns, L1 <4us Link: ASPM Disabled RCB 64 bytes Disabled CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x16 Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise- Slot: Number 1, PowerLimit 25.000000 Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- Slot: AttnInd Off, PwrInd On, Power- Root: Correctable- Non-Fatal- Fatal- PME- 41:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev b4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0 Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+ Device: Latency L0s <4us, L1 <16us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- Device: MaxPayload 128 bytes, MaxReadReq 128 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=41:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=0 CommitmentLimit=0 Downstream: Capacity=0 CommitmentLimit=0 Capabilities: [b0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 42:04.0 PCI bridge: Broadcom HT1000 PCI/PCI-X bridge (rev b2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- TAbort- Reset- FastB2B- Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv Status: Dev=42:04.0 64bit+ 133MHz+ SCD- USC- SCO- SRD- Upstream: Capacity=8 CommitmentLimit=8 Downstream: Capacity=8 CommitmentLimit=8 42:08.0 RAID bus controller: Hewlett-Packard Company Unknown device 3238 Subsystem: Hewlett-Packard Company Unknown device 3211 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- /dev/null 2>&1 || /cruc/usr/bin/sut_dispatcher >/cruc/suts/ca-ostest293/sut.log 2>&1 root 3899 0.0 0.0 64112 1024 ? S 20:23 0:00 /bin/bash -l /cruc/usr/bin/sut_dispatcher root 19775 0.0 0.0 0 0 ? S 22:25 0:00 [pdflush] root 19779 0.1 0.0 0 0 ? S 22:26 0:01 [pdflush] root 21462 0.0 0.0 63980 1160 ? S 22:38 0:00 /bin/bash /cruc/runs/6550/RUNNING/ca-ostest293/320-save_sysinfo root 21466 0.0 0.0 63980 1084 ? S 22:38 0:00 /bin/bash /cruc/usr/bin/sut_sysinfo root 21477 0.0 0.0 65748 968 ? R 22:38 0:00 ps auxw ========== chkconfig -l: ========== -l: unknown option ========== ifconfig: ========== eth0 Link encap:Ethernet HWaddr 00:18:FE:35:26:F6 inet addr:139.185.50.77 Bcast:139.185.51.255 Mask:255.255.252.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:347450 errors:0 dropped:0 overruns:0 frame:0 TX packets:236706 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:371198872 (354.0 MiB) TX bytes:129183488 (123.1 MiB) Interrupt:17 Memory:f8000000-f8012100 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:20 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1688 (1.6 KiB) TX bytes:1688 (1.6 KiB) ========== showmount: ========== mount clntudp_create: RPC: Program not registered ========== rpcinfo -p: ========== program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 922 status 100024 1 tcp 925 status 100021 1 tcp 13531 nlockmgr 100021 3 tcp 13531 nlockmgr 100021 4 tcp 13531 nlockmgr ========== exportfs -v: ========== ========== netstat: ========== Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost.localdomain:881 localhost.localdomai:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracle.:725 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.orac:rrimwm ca-fileserver3.us.or:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.o:rblcheckd ca-fileserver3.us.or:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracle.:861 ca-fileserver3.us.oracl:nfs TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:46198 ca-fileserver3.us.or:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracle.:659 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.orac:wpages ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:14573 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:58064 ca-fileserver3.us.oracl:nfs TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:23775 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us:entrust-ash ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:27313 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.oracle:3368 ca-fileserver3.us.or:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:14914 ca-ostest293.us.orac:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:41773 ca-fileserver3.us.oracl:nfs TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:46640 ca-fileserver3.us:acp-proto TIME_WAIT tcp 0 0 ca-ostest293.us.oracle.:834 ca-ostest292.us.oracle.:nfs ESTABLISHED tcp 0 0 ca-ostest293.us.oracle.:981 ca-fileserver3.us.oracl:nfs TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:21081 ca-fileserver3.us.or:sunrpc TIME_WAIT tcp 0 0 ca-ostest293.us.oracl:21474 ca-fileserver3.us.or:sunrpc TIME_WAIT Active UNIX domain sockets (w/o servers) Proto RefCnt Flags Type State I-Node Path unix 13 [ ] DGRAM 5911 /dev/log unix 2 [ ] DGRAM 514 @/org/kernel/udev/udevd unix 2 [ ] DGRAM 7750 @/org/freedesktop/hal/udev_event unix 3 [ ] STREAM CONNECTED 7859 /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 7858 unix 3 [ ] STREAM CONNECTED 7821 @/var/run/hald/dbus-qNugDk0CcQ unix 3 [ ] STREAM CONNECTED 7818 unix 3 [ ] STREAM CONNECTED 7806 @/var/run/hald/dbus-qNugDk0CcQ unix 3 [ ] STREAM CONNECTED 7803 unix 3 [ ] STREAM CONNECTED 7781 /var/run/acpid.socket unix 3 [ ] STREAM CONNECTED 7780 unix 3 [ ] STREAM CONNECTED 7775 @/var/run/hald/dbus-qNugDk0CcQ unix 3 [ ] STREAM CONNECTED 7771 unix 3 [ ] STREAM CONNECTED 7774 @/var/run/hald/dbus-qNugDk0CcQ unix 3 [ ] STREAM CONNECTED 7769 unix 3 [ ] STREAM CONNECTED 7745 @/var/run/hald/dbus-RhvhIXZlpb unix 3 [ ] STREAM CONNECTED 7744 unix 3 [ ] STREAM CONNECTED 7712 /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 7711 unix 3 [ ] STREAM CONNECTED 7706 unix 3 [ ] STREAM CONNECTED 7705 unix 2 [ ] DGRAM 7703 unix 3 [ ] STREAM CONNECTED 7695 /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 7694 unix 2 [ ] DGRAM 7681 unix 2 [ ] DGRAM 7651 unix 2 [ ] DGRAM 6744 unix 2 [ ] DGRAM 6713 unix 2 [ ] DGRAM 6682 unix 2 [ ] DGRAM 6654 unix 2 [ ] DGRAM 6580 unix 3 [ ] STREAM CONNECTED 6170 unix 3 [ ] STREAM CONNECTED 6169 unix 2 [ ] DGRAM 6041 unix 2 [ ] DGRAM 6035 unix 2 [ ] DGRAM 5921 unix 3 [ ] STREAM CONNECTED 5882 unix 3 [ ] STREAM CONNECTED 5881 ========== nfsstat: ========== Server rpc stats: calls badcalls badauth badclnt xdrcall 0 0 0 0 0 Client rpc stats: calls retrans authrefrsh 45688 0 0 Client nfs v3: null getattr setattr lookup access readlink 0 0% 2875 6% 580 1% 4708 10% 952 2% 0 0% read write create mkdir symlink mknod 10633 23% 11135 24% 1022 2% 3 0% 0 0% 0 0% remove rmdir rename link readdir readdirplus 900 1% 1 0% 2744 6% 0 0% 45 0% 82 0% fsstat fsinfo pathconf commit 135 0% 18 0% 0 0% 9852 21% ========== dmesg -s 1000000: ========== [ 0.000000] Linux version 2.6.25 (rdunlap@ca-ostest293.us.oracle.com) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-52)) #5 SMP Tue Jul 8 08:38:26 PDT 2008 [ 0.000000] Command line: ro root=LABEL=/ debug ignore_loglevel selinux=0 console=tty0 console=ttyS0,115200n8 3 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007fe50000 (usable) [ 0.000000] BIOS-e820: 000000007fe50000 - 000000007fe58000 (ACPI data) [ 0.000000] BIOS-e820: 000000007fe58000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) [ 0.000000] BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 000000027ffff000 (usable) [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 523856) 1 entries of 3200 used [ 0.000000] Entering add_active_range(0, 1048576, 2621439) 2 entries of 3200 used [ 0.000000] end_pfn_map = 2621439 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000F4F00, 0024 (r2 HP ) [ 0.000000] ACPI: XSDT 7FE50780, 005C (r1 HP A08 2 � 162E) [ 0.000000] ACPI: FACP 7FE50800, 00F4 (r3 HP A08 2 � 162E) [ 0.000000] ACPI: DSDT 7FE50900, 3F75 (r1 HP DSDT 1 INTL 20030228) [ 0.000000] ACPI: FACS 7FE50100, 0040 [ 0.000000] ACPI: SPCR 7FE50140, 0050 (r1 HP SPCRRBSU 1 � 162E) [ 0.000000] ACPI: MCFG 7FE501C0, 003C (r1 HP ProLiant 1 0) [ 0.000000] ACPI: HPET 7FE50200, 0038 (r1 HP A08 2 � 162E) [ 0.000000] ACPI: SPMI 7FE50240, 0040 (r5 HP ProLiant 1 � 162E) [ 0.000000] ACPI: APIC 7FE50280, 00DE (r1 HP 00000083 2 0) [ 0.000000] ACPI: SRAT 7FE50380, 0110 (r1 AMD HAMMER 1 AMD 1) [ 0.000000] SRAT: PXM 0 -> APIC 0 -> Node 0 [ 0.000000] SRAT: PXM 0 -> APIC 1 -> Node 0 [ 0.000000] SRAT: PXM 1 -> APIC 2 -> Node 1 [ 0.000000] SRAT: PXM 1 -> APIC 3 -> Node 1 [ 0.000000] SRAT: Node 0 PXM 0 0-a0000 [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used [ 0.000000] SRAT: Node 0 PXM 0 0-80000000 [ 0.000000] Entering add_active_range(0, 0, 159) 1 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 523856) 1 entries of 3200 used [ 0.000000] SRAT: Node 0 PXM 0 0-180000000 [ 0.000000] Entering add_active_range(0, 0, 159) 2 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 523856) 2 entries of 3200 used [ 0.000000] Entering add_active_range(0, 1048576, 1572864) 2 entries of 3200 used [ 0.000000] SRAT: Node 1 PXM 1 180000000-280000000 [ 0.000000] Entering add_active_range(1, 1572864, 2621439) 3 entries of 3200 used [ 0.000000] NUMA: Using 31 for the hash shift. [ 0.000000] Bootmem setup node 0 0000000000000000-0000000180000000 [ 0.000000] NODE_DATA [0000000000012000 - 0000000000018fff] [ 0.000000] bootmap [0000000000019000 - 0000000000048fff] pages 30 [ 0.000000] Bootmem setup node 1 0000000180000000-000000027ffff000 [ 0.000000] NODE_DATA [0000000180000000 - 0000000180006fff] [ 0.000000] bootmap [0000000180007000 - 0000000180026fff] pages 20 [ 0.000000] early res: 0 [0-fff] BIOS data page [ 0.000000] early res: 1 [6000-7fff] SMP_TRAMPOLINE [ 0.000000] early res: 2 [200000-7fa86f] TEXT DATA BSS [ 0.000000] early res: 3 [37ea5000-37fef242] RAMDISK [ 0.000000] early res: 4 [9f400-a03ff] EBDA [ 0.000000] early res: 5 [8000-11fff] PGTABLE [ 0.000000] [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0 [ 0.000000] [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0 [ 0.000000] [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0 [ 0.000000] [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0 [ 0.000000] [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0 [ 0.000000] [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0 [ 0.000000] [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0 [ 0.000000] [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0 [ 0.000000] [ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0 [ 0.000000] [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0 [ 0.000000] [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0 [ 0.000000] [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0 [ 0.000000] [ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0 [ 0.000000] [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0 [ 0.000000] [ffffe20003800000-ffffe200039fffff] PMD ->ffff810004a00000 on node 0 [ 0.000000] [ffffe20003a00000-ffffe20003bfffff] PMD ->ffff810004e00000 on node 0 [ 0.000000] [ffffe20003c00000-ffffe20003dfffff] PMD ->ffff810005200000 on node 0 [ 0.000000] [ffffe20003e00000-ffffe20003ffffff] PMD ->ffff810005600000 on node 0 [ 0.000000] [ffffe20004000000-ffffe200041fffff] PMD ->ffff810005a00000 on node 0 [ 0.000000] [ffffe20004200000-ffffe200043fffff] PMD ->ffff810005e00000 on node 0 [ 0.000000] [ffffe20004400000-ffffe200045fffff] PMD ->ffff810006200000 on node 0 [ 0.000000] [ffffe20004600000-ffffe200047fffff] PMD ->ffff810006600000 on node 0 [ 0.000000] [ffffe20004800000-ffffe200049fffff] PMD ->ffff810006a00000 on node 0 [ 0.000000] [ffffe20004a00000-ffffe20004bfffff] PMD ->ffff810006e00000 on node 0 [ 0.000000] [ffffe20004c00000-ffffe20004dfffff] PMD ->ffff810007200000 on node 0 [ 0.000000] [ffffe20004e00000-ffffe20004ffffff] PMD ->ffff810007600000 on node 0 [ 0.000000] [ffffe20005000000-ffffe200051fffff] PMD ->ffff810007a00000 on node 0 [ 0.000000] [ffffe20005200000-ffffe200053fffff] PMD ->ffff810007e00000 on node 0 [ 0.000000] [ffffe20005400000-ffffe200055fffff] PMD ->ffff810180200000 on node 1 [ 0.000000] [ffffe20005600000-ffffe200057fffff] PMD ->ffff810180400000 on node 1 [ 0.000000] [ffffe20005800000-ffffe200059fffff] PMD ->ffff810180600000 on node 1 [ 0.000000] [ffffe20005a00000-ffffe20005bfffff] PMD ->ffff810180800000 on node 1 [ 0.000000] [ffffe20005c00000-ffffe20005dfffff] PMD ->ffff810180a00000 on node 1 [ 0.000000] [ffffe20005e00000-ffffe20005ffffff] PMD ->ffff810180c00000 on node 1 [ 0.000000] [ffffe20006000000-ffffe200061fffff] PMD ->ffff810180e00000 on node 1 [ 0.000000] [ffffe20006200000-ffffe200063fffff] PMD ->ffff810181000000 on node 1 [ 0.000000] [ffffe20006400000-ffffe200065fffff] PMD ->ffff810181200000 on node 1 [ 0.000000] [ffffe20006600000-ffffe200067fffff] PMD ->ffff810181400000 on node 1 [ 0.000000] [ffffe20006800000-ffffe200069fffff] PMD ->ffff810181600000 on node 1 [ 0.000000] [ffffe20006a00000-ffffe20006bfffff] PMD ->ffff810181800000 on node 1 [ 0.000000] [ffffe20006c00000-ffffe20006dfffff] PMD ->ffff810181a00000 on node 1 [ 0.000000] [ffffe20006e00000-ffffe20006ffffff] PMD ->ffff810181c00000 on node 1 [ 0.000000] [ffffe20007000000-ffffe200071fffff] PMD ->ffff810181e00000 on node 1 [ 0.000000] [ffffe20007200000-ffffe200073fffff] PMD ->ffff810182000000 on node 1 [ 0.000000] [ffffe20007400000-ffffe200075fffff] PMD ->ffff810182200000 on node 1 [ 0.000000] [ffffe20007600000-ffffe200077fffff] PMD ->ffff810182400000 on node 1 [ 0.000000] [ffffe20007800000-ffffe200079fffff] PMD ->ffff810182600000 on node 1 [ 0.000000] [ffffe20007a00000-ffffe20007bfffff] PMD ->ffff810182800000 on node 1 [ 0.000000] [ffffe20007c00000-ffffe20007dfffff] PMD ->ffff810182a00000 on node 1 [ 0.000000] [ffffe20007e00000-ffffe20007ffffff] PMD ->ffff810182c00000 on node 1 [ 0.000000] [ffffe20008000000-ffffe200081fffff] PMD ->ffff810182e00000 on node 1 [ 0.000000] [ffffe20008200000-ffffe200083fffff] PMD ->ffff810183000000 on node 1 [ 0.000000] [ffffe20008400000-ffffe200085fffff] PMD ->ffff810183200000 on node 1 [ 0.000000] [ffffe20008600000-ffffe200087fffff] PMD ->ffff810183400000 on node 1 [ 0.000000] [ffffe20008800000-ffffe200089fffff] PMD ->ffff810183600000 on node 1 [ 0.000000] [ffffe20008a00000-ffffe20008bfffff] PMD ->ffff810183800000 on node 1 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 2621439 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[4] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 523856 [ 0.000000] 0: 1048576 -> 1572864 [ 0.000000] 1: 1572864 -> 2621439 [ 0.000000] On node 0 totalpages: 1048047 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1546 pages reserved [ 0.000000] DMA zone: 2397 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 505480 pages, LIFO batch:31 [ 0.000000] Normal zone: 7168 pages used for memmap [ 0.000000] Normal zone: 517120 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] On node 1 totalpages: 1048575 [ 0.000000] DMA zone: 0 pages used for memmap [ 0.000000] DMA32 zone: 0 pages used for memmap [ 0.000000] Normal zone: 14335 pages used for memmap [ 0.000000] Normal zone: 1034240 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Detected use of extended apic ids on hypertransport bus [ 0.000000] Detected use of extended apic ids on hypertransport bus [ 0.000000] ACPI: PM-Timer IO Port: 0x908 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] Processor #2 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) [ 0.000000] Processor #3 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xf7df0000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, address 0xf7df0000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x09] address[0xfdef0000] gsi_base[38]) [ 0.000000] IOAPIC[1]: apic_id 9, address 0xfdef0000, GSI 38-61 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x10228201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 000000007fe50000 - 000000007fe58000 [ 0.000000] PM: Registered nosave memory: 000000007fe58000 - 0000000080000000 [ 0.000000] PM: Registered nosave memory: 0000000080000000 - 00000000fec00000 [ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed00000 [ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fee00000 [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee10000 [ 0.000000] PM: Registered nosave memory: 00000000fee10000 - 00000000ffc00000 [ 0.000000] PM: Registered nosave memory: 00000000ffc00000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000) [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 42176 bytes of per cpu data [ 0.000000] Built 2 zonelists in Zone order, mobility grouping on. Total pages: 2059237 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: ro root=LABEL=/ debug ignore_loglevel selinux=0 console=tty0 console=ttyS0,115200n8 3 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Extended CMOS year: 2000 [ 0.000000] TSC calibrated against PM_TIMER [ 0.000001] Marking TSC unstable due to TSCs unsynchronized [ 0.000003] time.c: Detected 2612.031 MHz processor. [ 0.000010] spurious 8259A interrupt: IRQ7. [ 0.004000] Console: colour VGA+ 80x25 [ 0.004000] console [tty0] enabled [ 0.004000] console [ttyS0] enabled [ 0.004000] Checking aperture... [ 0.004000] Node 0: aperture @ fa6c000000 size 32 MB [ 0.004000] Aperture beyond 4GB. Ignoring. [ 0.004000] No AGP bridge found [ 0.004000] Your BIOS doesn't leave a aperture memory hole [ 0.004000] Please enable the IOMMU option in the BIOS setup [ 0.004000] This costs you 64 MB of RAM [ 0.004000] Mapping aperture over 65536 KB of RAM @ c000000 [ 0.004000] PM: Registered nosave memory: 000000000c000000 - 0000000010000000 [ 0.004000] Memory: 8197928k/10485756k available (3303k kernel code, 188560k reserved, 1471k data, 348k init) [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated [ 0.004000] SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=2 [ 0.004000] hpet clockevent registered [ 0.080006] Calibrating delay using timer specific routine.. 5226.94 BogoMIPS (lpj=10453885) [ 0.082364] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.088031] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.090847] Mount-cache hash table entries: 256 [ 0.092171] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.092618] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.093004] CPU 0/0 -> Node 0 [ 0.093826] CPU: Physical Processor ID: 0 [ 0.096007] CPU: Processor Core ID: 0 [ 0.097012] ACPI: Core revision 20070126 [ 0.147223] Using local APIC timer interrupts. [ 0.152010] APIC timer calibration result 12557880 [ 0.156011] Detected 12.557 MHz APIC timer. [ 0.160147] Booting processor 1/4 APIC 0x2 [ 0.004000] Initializing CPU#1 [ 0.004000] Calibrating delay using timer specific routine.. 5224.18 BogoMIPS (lpj=10448365) [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.004000] CPU 1/2 -> Node 1 [ 0.004000] CPU: Physical Processor ID: 1 [ 0.004000] CPU: Processor Core ID: 0 [ 0.004000] Dual-Core AMD Opteron(tm) Processor 8218 stepping 02 [ 0.252245] Booting processor 2/4 APIC 0x1 [ 0.004000] Initializing CPU#2 [ 0.004000] Calibrating delay using timer specific routine.. 5224.16 BogoMIPS (lpj=10448323) [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.004000] CPU 2/1 -> Node 0 [ 0.004000] CPU: Physical Processor ID: 0 [ 0.004000] CPU: Processor Core ID: 1 [ 0.004000] Dual-Core AMD Opteron(tm) Processor 8218 stepping 02 [ 0.348252] Booting processor 3/4 APIC 0x3 [ 0.004000] Initializing CPU#3 [ 0.004000] Calibrating delay using timer specific routine.. 5224.19 BogoMIPS (lpj=10448384) [ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.004000] CPU: L2 Cache: 1024K (64 bytes/line) [ 0.004000] CPU 3/3 -> Node 1 [ 0.004000] CPU: Physical Processor ID: 1 [ 0.004000] CPU: Processor Core ID: 1 [ 0.004000] Dual-Core AMD Opteron(tm) Processor 8218 stepping 02 [ 0.444248] Brought up 4 CPUs [ 0.524031] khelper used greatest stack depth: 6120 bytes left [ 0.464030] net_namespace: 304 bytes [ 0.464158] NET: Registered protocol family 16 [ 0.468124] ACPI: bus type pci registered [ 0.472079] PCI: BIOS Bug: MCFG area at 80000000 is not E820-reserved [ 0.476032] PCI: Not using MMCONFIG. [ 0.480032] PCI: Using configuration type 1 [ 0.488032] ACPI: EC: Look up EC in DSDT [ 0.490230] ACPI: SSDT 7FE58000, 04F0 (r2 HP PNOWSSDT 2 HP 1) [ 0.496501] ACPI: Interpreter enabled [ 0.500036] ACPI: (supports S0 S4 S5) [ 0.504929] ACPI: Using IOAPIC for interrupt routing [ 0.513096] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.524034] PCI: Transparent bridge - 0000:00:09.0 [ 0.524581] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.528111] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT] [ 0.532143] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT] [ 0.536128] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1.NB01._PRT] [ 0.540099] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2.NC1B._PRT] [ 0.544084] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE3.NC2B._PRT] [ 0.552132] ACPI: PCI Root Bridge [PCI1] (0000:40) [ 0.556408] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT] [ 0.560141] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT] [ 0.564140] ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2.SASB._PRT] [ 0.568560] ACPI: PCI Interrupt Link [LNKW] (IRQs 16) *0, disabled. [ 0.576464] ACPI: PCI Interrupt Link [LNKX] (IRQs 17) *0, disabled. [ 0.585375] ACPI: PCI Interrupt Link [LNKY] (IRQs 18) *0, disabled. [ 0.596149] ACPI: PCI Interrupt Link [LNKZ] (IRQs 19) *0, disabled. [ 0.605352] ACPI: PCI Interrupt Link [LNU0] (IRQs 22) *5 [ 0.609463] ACPI: PCI Interrupt Link [LNU2] (IRQs 23) *7 [ 0.614655] ACPI: PCI Interrupt Link [LNKA] (IRQs 54) *0, disabled. [ 0.624451] ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled. [ 0.632467] ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled. [ 0.644480] ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled. [ 0.656435] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.660059] pnp: PnP ACPI init [ 0.664048] ACPI: bus type pnp registered [ 0.673273] pnp: PnP ACPI: found 11 devices [ 0.676045] ACPI: ACPI bus type pnp unregistered [ 0.680206] SCSI subsystem initialized [ 0.684107] usbcore: registered new interface driver usbfs [ 0.688074] usbcore: registered new interface driver hub [ 0.692075] usbcore: registered new device driver usb [ 0.696157] PCI: Using ACPI for IRQ routing [ 0.700047] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.724047] PCI-DMA: Disabling AGP. [ 0.728448] PCI-DMA: aperture base @ c000000 size 65536 KB [ 0.732049] PCI-DMA: using GART IOMMU. [ 0.736051] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture [ 0.740663] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31 [ 0.749286] hpet0: 3 32-bit timers, 25000000 Hz [ 0.772055] system 00:01: ioport range 0x408-0x40f has been reserved [ 0.772057] system 00:01: ioport range 0x4d0-0x4d1 has been reserved [ 0.776057] system 00:01: ioport range 0x700-0x73f has been reserved [ 0.780057] system 00:01: ioport range 0x800-0x8fe has been reserved [ 0.784057] system 00:01: ioport range 0x900-0x9fe has been reserved [ 0.788057] system 00:01: ioport range 0x9ff-0x9ff has been reserved [ 0.792058] system 00:01: ioport range 0xa00-0xafe has been reserved [ 0.796058] system 00:01: ioport range 0xaff-0xaff has been reserved [ 0.800058] system 00:01: ioport range 0xb00-0xbfe has been reserved [ 0.804058] system 00:01: ioport range 0xbff-0xbff has been reserved [ 0.808059] system 00:01: ioport range 0xc80-0xc83 has been reserved [ 0.812059] system 00:01: ioport range 0xcd4-0xcd7 has been reserved [ 0.816059] system 00:01: ioport range 0xf50-0xf58 has been reserved [ 0.820059] system 00:01: ioport range 0xca0-0xca1 has been reserved [ 0.824060] system 00:01: ioport range 0xca4-0xca5 has been reserved [ 0.828060] system 00:01: ioport range 0xcf9-0xcf9 could not be reserved [ 0.832060] system 00:01: ioport range 0x3f8-0x3ff has been reserved [ 0.836061] system 00:01: iomem range 0x80000000-0x8fffffff has been reserved [ 0.840061] system 00:01: iomem range 0xf7df0000-0xf7df0fff has been reserved [ 0.844061] system 00:01: iomem range 0xfdef0000-0xfdef0fff has been reserved [ 0.848703] PCI: Bridge: 0000:00:09.0 [ 0.852062] IO window: 1000-2fff [ 0.856062] MEM window: 0xf7e00000-0xf7ffffff [ 0.860062] PREFETCH window: 0x00000000e8000000-0x00000000efffffff [ 0.864063] PCI: Bridge: 0000:02:00.0 [ 0.868062] IO window: disabled. [ 0.872064] MEM window: 0xf8000000-0xf9ffffff [ 0.876063] PREFETCH window: disabled. [ 0.880065] PCI: Bridge: 0000:00:0b.0 [ 0.884063] IO window: disabled. [ 0.888064] MEM window: 0xf8000000-0xf9ffffff [ 0.892064] PREFETCH window: disabled. [ 0.896065] PCI: Bridge: 0000:04:00.0 [ 0.900064] IO window: disabled. [ 0.904066] MEM window: 0xfa000000-0xfbffffff [ 0.908065] PREFETCH window: disabled. [ 0.912067] PCI: Bridge: 0000:00:0c.0 [ 0.916065] IO window: disabled. [ 0.920066] MEM window: 0xfa000000-0xfbffffff [ 0.924066] PREFETCH window: disabled. [ 0.928067] PCI: Bridge: 0000:06:00.0 [ 0.932066] IO window: disabled. [ 0.936068] MEM window: 0xfdc00000-0xfdcfffff [ 0.940067] PREFETCH window: disabled. [ 0.944069] PCI: Bridge: 0000:00:0d.0 [ 0.948067] IO window: disabled. [ 0.952068] MEM window: 0xfdc00000-0xfdcfffff [ 0.956068] PREFETCH window: disabled. [ 0.960069] PCI: Bridge: 0000:00:0e.0 [ 0.964068] IO window: 3000-3fff [ 0.968069] MEM window: 0xfdd00000-0xfddfffff [ 0.972069] PREFETCH window: disabled. [ 0.976074] PCI: Setting latency timer of device 0000:00:09.0 to 64 [ 0.980077] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 0.984079] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 0.988074] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 0.992079] PCI: Setting latency timer of device 0000:04:00.0 to 64 [ 0.996074] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 1.000081] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 1.004074] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 1.008073] PCI: Bridge: 0000:42:04.0 [ 1.012071] IO window: disabled. [ 1.016073] MEM window: disabled. [ 1.020073] PREFETCH window: disabled. [ 1.024075] PCI: Bridge: 0000:41:00.0 [ 1.028073] IO window: 4000-4fff [ 1.032074] MEM window: 0xfdf00000-0xfdffffff [ 1.036074] PREFETCH window: disabled. [ 1.040075] PCI: Bridge: 0000:40:0c.0 [ 1.044073] IO window: 4000-4fff [ 1.048074] MEM window: 0xfdf00000-0xfdffffff [ 1.052074] PREFETCH window: disabled. [ 1.056075] PCI: Bridge: 0000:40:0d.0 [ 1.060074] IO window: disabled. [ 1.064075] MEM window: disabled. [ 1.068075] PREFETCH window: disabled. [ 1.072076] PCI: Bridge: 0000:40:0e.0 [ 1.076075] IO window: disabled. [ 1.080076] MEM window: disabled. [ 1.084076] PREFETCH window: disabled. [ 1.088081] PCI: Setting latency timer of device 0000:40:0c.0 to 64 [ 1.092086] PCI: Setting latency timer of device 0000:41:00.0 to 64 [ 1.096086] PCI: Setting latency timer of device 0000:40:0d.0 to 64 [ 1.100080] PCI: Setting latency timer of device 0000:40:0e.0 to 64 [ 1.104171] NET: Registered protocol family 2 [ 1.152080] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 1.156258] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.167323] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.168636] TCP: Hash tables configured (established 524288 bind 65536) [ 1.172082] TCP reno registered [ 1.192084] checking if image is initramfs... it is [ 1.261179] Freeing initrd memory: 1320k freed [ 1.269370] microcode: CPU0 not a capable Intel processor [ 4.012393] microcode: CPU1 not a capable Intel processor [ 3.820498] microcode: CPU2 not a capable Intel processor [ 3.644218] microcode: CPU3 not a capable Intel processor [ 3.644221] IA-32 Microcode Update Driver: v1.14a [ 3.652603] audit: initializing netlink socket (disabled) [ 3.656238] type=2000 audit(1250886098.247:1): initialized [ 3.660836] Total HugeTLB memory allocated, 0 [ 3.672294] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.676500] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 3.680223] io scheduler noop registered [ 3.684223] io scheduler anticipatory registered [ 3.688223] io scheduler deadline registered [ 3.692374] io scheduler cfq registered (default) [ 3.696241] pci 0000:00:00.0: Enabling HT MSI Mapping [ 3.736226] pci 0000:00:0b.0: Enabling HT MSI Mapping [ 3.736232] pci 0000:00:0b.0: Found enabled HT MSI Mapping [ 3.740234] pci 0000:00:0c.0: Enabling HT MSI Mapping [ 3.744232] pci 0000:00:0c.0: Found enabled HT MSI Mapping [ 3.748234] pci 0000:00:0d.0: Enabling HT MSI Mapping [ 3.752232] pci 0000:00:0d.0: Found enabled HT MSI Mapping [ 3.756234] pci 0000:00:0e.0: Enabling HT MSI Mapping [ 3.760232] pci 0000:00:0e.0: Found enabled HT MSI Mapping [ 3.764238] pci 0000:01:03.0: Boot video device [ 3.768242] pci 0000:01:04.4: HCRESET not completed yet! [ 3.772247] pci 0000:40:00.0: Enabling HT MSI Mapping [ 3.776241] pci 0000:40:0c.0: Enabling HT MSI Mapping [ 3.780234] pci 0000:40:0c.0: Found enabled HT MSI Mapping [ 3.784236] pci 0000:40:0d.0: Enabling HT MSI Mapping [ 3.788234] pci 0000:40:0d.0: Found enabled HT MSI Mapping [ 3.792237] pci 0000:40:0e.0: Enabling HT MSI Mapping [ 3.796234] pci 0000:40:0e.0: Found enabled HT MSI Mapping [ 2.009042] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 2.009057] assign_interrupt_mode Found MSI capability [ 2.013058] Allocate Port Service[0000:00:0b.0:pcie00] [ 2.017123] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 2.021055] assign_interrupt_mode Found MSI capability [ 2.025054] Allocate Port Service[0000:00:0c.0:pcie00] [ 2.029107] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 2.033056] assign_interrupt_mode Found MSI capability [ 2.037054] Allocate Port Service[0000:00:0d.0:pcie00] [ 2.041105] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 2.045056] assign_interrupt_mode Found MSI capability [ 2.049055] Allocate Port Service[0000:00:0e.0:pcie00] [ 5.074536] PCI: Setting latency timer of device 0000:40:0c.0 to 64 [ 5.074552] assign_interrupt_mode Found MSI capability [ 5.078555] Allocate Port Service[0000:40:0c.0:pcie00] [ 5.082620] PCI: Setting latency timer of device 0000:40:0d.0 to 64 [ 5.086549] assign_interrupt_mode Found MSI capability [ 5.090550] Allocate Port Service[0000:40:0d.0:pcie00] [ 5.094601] PCI: Setting latency timer of device 0000:40:0e.0 to 64 [ 5.098550] assign_interrupt_mode Found MSI capability [ 5.102548] Allocate Port Service[0000:40:0e.0:pcie00] [ 5.107134] input: Power Button (FF) as /class/input/input0 [ 5.110541] ACPI: Power Button (FF) [PWRF] [ 5.114826] ACPI: ACPI0007:00 is registered as cooling_device0 [ 5.118600] ACPI: ACPI0007:01 is registered as cooling_device1 [ 5.122600] ACPI: ACPI0007:02 is registered as cooling_device2 [ 5.126600] ACPI: ACPI0007:03 is registered as cooling_device3 [ 5.158618] Real Time Clock Driver v1.12ac [ 5.158714] hpet_resources: 0xfed00000 is busy [ 5.162710] Non-volatile memory driver v1.2 [ 5.166638] Linux agpgart interface v0.103 [ 5.170771] [drm] Initialized drm 1.1.0 20060810 [ 5.174859] ACPI: PCI Interrupt Link [LNKY] enabled at IRQ 18 [ 5.178624] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKY] -> GSI 18 (level, high) -> IRQ 18 [ 5.190712] [drm] Initialized radeon 1.28.0 20060524 on minor 0 [ 5.194727] ipmi message handler version 39.1 [ 5.198623] ipmi device interface [ 5.202701] IPMI System Interface driver. [ 5.206625] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0 [ 5.312444] ipmi: Found new BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11) [ 5.312500] IPMI kcs interface initialized [ 5.316457] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0 [ 5.320447] ipmi_si: duplicate interface [ 3.041846] ACPI: PCI Interrupt Link [LNKW] enabled at IRQ 16 [ 3.041852] ACPI: PCI Interrupt 0000:01:04.6[A] -> Link [LNKW] -> GSI 16 (level, high) -> IRQ 16 [ 3.048002] ipmi_si: Trying PCI-specified kcs state machine at mem address 0xf7ef0000, slave address 0x0, irq 16 [ 3.137852] Using irq 16 [ 3.330353] ipmi: interfacing existing BMC (man_id: 0x00000b, prod_id: 0x0000, dev_id: 0x11) [ 3.330425] IPMI kcs interface initialized [ 3.346335] IPMI Watchdog: driver initialized [ 3.346355] Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot. [ 3.361916] IPMI poweroff: ATCA Detect mfg 0xB prod 0x0 [ 3.362356] IPMI poweroff: Unable to find a poweroff function that will work, giving up [ 5.774351] IPMI poweroff: ATCA Detect mfg 0xB prod 0x0 [ 5.777977] IPMI poweroff: Unable to find a poweroff function that will work, giving up [ 5.797975] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). [ 5.797976] Hangcheck: Using get_cycles(). [ 5.801980] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 5.806086] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 5.810091] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 5.814340] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 5.818228] Floppy drive(s): fd0 is 1.44M [ 8.853966] floppy0: no floppy controllers found [ 8.854848] brd: module loaded [ 8.858011] Fixed MDIO Bus: probed [ 8.861972] tun: Universal TUN/TAP device driver, 1.6 [ 8.865968] tun: (C) 1999-2004 Max Krasnyansky [ 8.870015] console [netcon0] enabled [ 8.873969] netconsole: network logging started [ 8.878431] Loading iSCSI transport class v2.0-869. [ 8.882373] Driver 'sd' needs updating - please use bus_type methods [ 8.886237] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12 [ 8.891586] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 8.893974] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 8.898087] mice: PS/2 mouse device common for all mice [ 8.994678] input: PC Speaker as /class/input/input1 [ 9.034732] i2c /dev entries driver [ 7.162092] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 7.165902] EDAC MC: Ver: 2.1.0 Jul 8 2008 [ 7.170332] cpuidle: using governor ladder [ 7.173993] usbcore: registered new interface driver hiddev [ 7.177956] usbcore: registered new interface driver usbhid [ 7.181903] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 7.186197] IPv4 over IPv4 tunneling driver [ 7.190100] GRE over IPv4 tunneling driver [ 7.194136] TCP bic registered [ 7.197903] Initializing XFRM netlink socket [ 7.201916] NET: Registered protocol family 1 [ 7.205917] NET: Registered protocol family 17 [ 7.209908] NET: Registered protocol family 15 [ 7.214106] RPC: Registered udp transport module. [ 7.217904] RPC: Registered tcp transport module. [ 9.420877] powernow-k8: Found 2 Dual-Core AMD Opteron(tm) Processor 8218 processors (4 cpu cores) (version 2.20.00) [ 7.270549] powernow-k8: 0 : fid 0x12 (2600 MHz), vid 0x8 [ 7.270551] powernow-k8: 1 : fid 0x10 (2400 MHz), vid 0xa [ 7.274550] powernow-k8: 2 : fid 0xe (2200 MHz), vid 0xc [ 7.278551] powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xe [ 7.282550] powernow-k8: 4 : fid 0xa (1800 MHz), vid 0x10 [ 7.286551] powernow-k8: 5 : fid 0x2 (1000 MHz), vid 0x12 [ 10.301124] powernow-k8: 0 : fid 0x12 (2600 MHz), vid 0x8 [ 10.301127] powernow-k8: 1 : fid 0x10 (2400 MHz), vid 0xa [ 10.305128] powernow-k8: 2 : fid 0xe (2200 MHz), vid 0xc [ 10.309127] powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xe [ 10.313127] powernow-k8: 4 : fid 0xa (1800 MHz), vid 0x10 [ 10.317127] powernow-k8: 5 : fid 0x2 (1000 MHz), vid 0x12 [ 10.321400] registered taskstats version 1 [ 10.325271] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 10.329129] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found [ 10.333385] Freeing unused kernel memory: 348k freed [ 10.337327] Write protecting the kernel read-only data: 1132k [ 11.434803] USB Universal Host Controller Interface driver v3.0 [ 11.435068] ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17 [ 11.438809] ACPI: PCI Interrupt 0000:01:04.4[B] -> Link [LNKX] -> GSI 17 (level, high) -> IRQ 17 [ 11.448394] uhci_hcd 0000:01:04.4: UHCI Host Controller [ 11.450883] uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 1 [ 11.454813] uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports [ 11.458815] uhci_hcd 0000:01:04.4: HCRESET not completed yet! [ 11.462817] uhci_hcd 0000:01:04.4: irq 17, io base 0x00001800 [ 11.466937] usb usb1: configuration #1 chosen from 1 choice [ 11.470829] hub 1-0:1.0: USB hub found [ 11.474812] hub 1-0:1.0: 2 ports detected [ 11.586836] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.586838] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.590837] usb usb1: Product: UHCI Host Controller [ 11.594838] usb usb1: Manufacturer: Linux 2.6.25 uhci_hcd [ 11.598838] usb usb1: SerialNumber: 0000:01:04.4 [ 11.602906] insmod used greatest stack depth: 5352 bytes left [ 11.222973] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.530925] ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22 [ 8.530931] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNU0] -> GSI 22 (level, high) -> IRQ 22 [ 8.542934] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 10.939181] usb 1-1: new full speed USB device using uhci_hcd and address 2 [ 8.546929] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 8.550989] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 8.554949] ohci_hcd 0000:00:02.0: irq 22, io mem 0xf7de0000 [ 8.618931] usb usb2: configuration #1 chosen from 1 choice [ 8.618954] hub 2-0:1.0: USB hub found [ 8.622939] hub 2-0:1.0: 10 ports detected [ 11.289652] usb 1-1: configuration #1 chosen from 1 choice [ 11.302280] input: HP Virtual Keyboard as /class/input/input2 [ 8.734989] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 8.734991] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.734993] usb usb2: Product: OHCI Host Controller [ 8.734994] usb usb2: Manufacturer: Linux 2.6.25 ohci_hcd [ 8.734996] usb usb2: SerialNumber: 0000:00:02.0 [ 12.268663] ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23 [ 12.268668] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LNU2] -> GSI 23 (level, high) -> IRQ 23 [ 12.278887] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 12.280665] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 12.284717] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3 [ 12.288689] ehci_hcd 0000:00:02.1: debug port 1 [ 12.292667] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 12.296674] ehci_hcd 0000:00:02.1: irq 23, io mem 0xf7dd0000 [ 12.316667] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 12.316746] usb usb3: configuration #1 chosen from 1 choice [ 12.320689] hub 3-0:1.0: USB hub found [ 12.324675] hub 3-0:1.0: 10 ports detected [ 11.695290] input,hidraw0: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1 [ 11.716825] input: HP Virtual Keyboard as /class/input/input3 [ 12.438596] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.745347] input,hidraw1: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1 [ 11.747990] usb 1-1: New USB device found, idVendor=03f0, idProduct=1027 [ 11.747990] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 11.747990] usb 1-1: Product: Virtual Keyboard [ 11.747990] usb 1-1: Manufacturer: HP [ 12.438607] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.442597] usb usb3: Product: EHCI Host Controller [ 12.446597] usb usb3: Manufacturer: Linux 2.6.25 ehci_hcd [ 11.988888] usb 1-2: new full speed USB device using uhci_hcd and address 3 [ 12.450673] usb usb3: SerialNumber: 0000:00:02.1 [ 12.651781] HP CISS Driver (v 3.6.14) [ 12.656084] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54 [ 12.659764] ACPI: PCI Interrupt 0000:42:08.0[A] -> <6>usb 1-2: configuration #1 chosen from 1 choice [ 12.540795] hub 1-2:1.0: USB hub found [ 12.543065] hub 1-2:1.0: 7 ports detected [ 12.663759] Link [LNKA] -> GSI 54 (level, high) -> IRQ 54 [ 12.715762] cciss0: <0x3238> at PCI 0000:42:08.0 IRQ 504 using DAC [ 12.274721] usb 1-2: New USB device found, idVendor=03f0, idProduct=1327 [ 12.731759] blocks= 286677120 block_size= 512 [ 12.735761] heads=255, sectors=32, cylinders=35132 [ 12.735762] [ 12.739758] blocks= 286677120 block_size= 512 [ 12.743762] heads=255, sectors=32, cylinders=35132 [ 12.743763] [ 12.743857] blocks= 286677120 block_size= 512 [ 12.743962] heads=255, sectors=32, cylinders=35132 [ 12.743962] [ 12.743962] cciss/c0d0: p1 p2 p3 p4 [ 12.274728] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.971237] blocks= 286677120 block_size= 512 [ 12.971347] heads=255, sectors=32, cylinders=35132 [ 12.971348] [ 12.971349] cciss/c0d1: p1 p2 [ 12.278724] usb 1-2: Product: Virtual Hub [ 12.282723] usb 1-2: Manufacturer: HP [ 13.099729] insmod used greatest stack depth: 4432 bytes left [ 13.286274] EXT3-fs: INFO: recovery required on readonly filesystem. [ 13.286396] EXT3-fs: write access will be enabled during recovery. [ 14.605084] kjournald starting. Commit interval 5 seconds [ 15.684984] EXT3-fs: cciss/c0d0p3: orphan cleanup on readonly fs [ 15.684985] ext3_orphan_cleanup: deleting unreferenced inode 11698196 [ 15.702933] ext3_orphan_cleanup: deleting unreferenced inode 11698194 [ 15.723711] ext3_orphan_cleanup: deleting unreferenced inode 11698197 [ 15.743827] ext3_orphan_cleanup: deleting unreferenced inode 9347229 [ 15.771222] EXT3-fs: cciss/c0d0p3: 4 orphan inodes deleted [ 15.771223] EXT3-fs: recovery complete. [ 16.185617] EXT3-fs: mounted filesystem with ordered data mode. [ 16.697165] modprobe used greatest stack depth: 3584 bytes left [ 19.144005] Emulex LightPulse Fibre Channel SCSI driver 8.2.5 [ 19.147412] Copyright(c) 2004-2008 Emulex. All rights reserved. [ 19.165189] ACPI: PCI Interrupt 0000:08:00.0[A] -> Link [LNKY] -> GSI 18 (level, high) -> IRQ 18 [ 19.176156] PCI: Setting latency timer of device 0000:08:00.0 to 64 [ 19.184141] scsi0 : on PCI bus 08 device 00 irq 18 [ 27.268107] lpfc 0000:08:00.0: 0:1303 Link Up Event x1 received Data: x1 xf7 x10 x2 [ 28.287048] scsi 0:0:0:0: RAID COMPAQ MSA1000 5.20 PQ: 0 ANSI: 4 [ 29.904517] ACPI: PCI Interrupt Link [LNKZ] enabled at IRQ 19 [ 29.904517] ACPI: PCI Interrupt 0000:08:00.1[B] -> Link [LNKZ] -> GSI 19 (level, high) -> IRQ 19 [ 29.904517] PCI: Setting latency timer of device 0000:08:00.1 to 64 [ 29.904545] scsi1 : on PCI bus 08 device 01 irq 19 [ 28.291066] scsi 0:0:0:0: Attached scsi generic sg0 type 12 [ 28.303270] scsi 0:0:0:8: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 [ 28.304164] sd 0:0:0:8: [sda] 2187605616 512-byte hardware sectors (1120054 MB) [ 28.307575] sd 0:0:0:8: [sda] Write Protect is off [ 28.311272] sd 0:0:0:8: [sda] Mode Sense: 83 00 00 08 [ 28.315862] sd 0:0:0:8: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 28.319814] sd 0:0:0:8: [sda] 2187605616 512-byte hardware sectors (1120054 MB) [ 28.323584] sd 0:0:0:8: [sda] Write Protect is off [ 28.327273] sd 0:0:0:8: [sda] Mode Sense: 83 00 00 08 [ 28.331887] sd 0:0:0:8: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 28.335273] sda: sda1 [ 28.343596] sd 0:0:0:8: [sda] Attached SCSI disk [ 28.347309] sd 0:0:0:8: Attached scsi generic sg1 type 0 [ 28.352600] scsi 0:0:1:0: Enclosure HP MSA2212fc J200 PQ: 0 ANSI: 5 [ 28.355340] scsi 0:0:1:0: Attached scsi generic sg2 type 13 [ 28.365672] scsi 0:0:2:0: RAID COMPAQ MSA1000 5.20 PQ: 0 ANSI: 4 [ 28.369429] scsi 0:0:2:0: Attached scsi generic sg3 type 12 [ 37.346510] lpfc 0000:08:00.1: 1:1303 Link Up Event x1 received Data: x1 xf7 x10 x2 [ 37.094269] scsi 1:0:0:0: RAID COMPAQ MSA1000 5.20 PQ: 0 ANSI: 4 [ 37.096233] scsi 1:0:0:0: Attached scsi generic sg4 type 12 [ 40.619351] tg3.c:v3.90 (April 12, 2008) [ 37.100289] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.7.4 (February 18, 2008) [ 37.100311] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKX] -> GSI 17 (level, high) -> IRQ 17 [ 37.100591] eth0: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 17, node addr 00:18:fe:35:26:f6 [ 37.100611] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKW] -> GSI 16 (level, high) -> IRQ 16 [ 37.100865] eth1: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 16, node addr 00:18:fe:35:26:f4 [ 38.447835] scsi 1:0:0:8: Direct-Access COMPAQ MSA1000 VOLUME 5.20 PQ: 0 ANSI: 4 [ 38.448080] sd 1:0:0:8: [sdb] 2187605616 512-byte hardware sectors (1120054 MB) [ 38.448080] sd 1:0:0:8: [sdb] Write Protect is off [ 38.448080] sd 1:0:0:8: [sdb] Mode Sense: 83 00 00 08 [ 38.448080] sd 1:0:0:8: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 38.448080] sd 1:0:0:8: [sdb] 2187605616 512-byte hardware sectors (1120054 MB) [ 38.448080] sd 1:0:0:8: [sdb] Write Protect is off [ 38.448080] sd 1:0:0:8: [sdb] Mode Sense: 83 00 00 08 [ 38.448080] sd 1:0:0:8: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 38.448080] sdb: sdb1 [ 40.623232] ACPI: PCI Interrupt 0000:07:04.0[A] -> <5>sd 1:0:0:8: [sdb] Attached SCSI disk [ 38.985456] sd 1:0:0:8: Attached scsi generic sg5 type 0 [ 38.992114] scsi 1:0:1:0: RAID COMPAQ MSA1000 5.20 PQ: 0 ANSI: 4 [ 38.992114] scsi 1:0:1:0: Attached scsi generic sg6 type 12 [ 38.992760] scsi 1:0:2:0: Enclosure HP MSA2212fc J200 PQ: 0 ANSI: 5 [ 38.992839] scsi 1:0:2:0: Attached scsi generic sg7 type 13 [ 40.627205] Link [LNKZ] -> GSI 19 (level, high) -> IRQ 19 [ 40.655518] eth2: Tigon3 [partno(011276-001) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 1000Base-SX Ethernet 00:18:fe:34:1c:2f [ 40.659410] eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1] [ 40.663412] eth2: dma_rwctrl[76148000] dma_mask[40-bit] [ 40.667692] ACPI: PCI Interrupt 0000:07:04.1[B] -> Link [LNKW] -> GSI 16 (level, high) -> IRQ 16 [ 40.699461] eth3: Tigon3 [partno(011276-001) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 1000Base-SX Ethernet 00:18:fe:34:1c:30 [ 40.703422] eth3: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1] [ 40.707439] eth3: dma_rwctrl[76148000] dma_mask[40-bit] [ 41.524096] lp: driver loaded but no devices found [ 42.182824] EXT3 FS on cciss/c0d0p3, internal journal [ 41.057435] kjournald starting. Commit interval 5 seconds [ 42.269208] EXT3 FS on cciss/c0d0p1, internal journal [ 42.269208] EXT3-fs: mounted filesystem with ordered data mode. [ 42.269538] VFS: Can't find ext3 filesystem on dev cciss/c0d0p4. [ 41.071076] kjournald starting. Commit interval 5 seconds [ 42.405105] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended [ 42.419527] EXT3 FS on cciss/c0d1p1, internal journal [ 42.419527] EXT3-fs: recovery complete. [ 42.419527] EXT3-fs: mounted filesystem with writeback data mode. [ 41.210113] kjournald starting. Commit interval 5 seconds [ 42.664198] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended [ 42.673724] EXT3 FS on cciss/c0d1p2, internal journal [ 42.673724] EXT3-fs: recovery complete. [ 42.679880] EXT3-fs: mounted filesystem with writeback data mode. [ 41.218653] kjournald starting. Commit interval 5 seconds [ 41.218660] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended [ 41.223253] EXT3 FS on sda1, internal journal [ 41.230655] EXT3-fs: recovery complete. [ 41.234658] EXT3-fs: mounted filesystem with writeback data mode. [ 43.357352] Adding 8385920k swap on /dev/cciss/c0d0p2. Priority:-1 extents:1 across:8385920k [ 43.413532] rc.sysinit used greatest stack depth: 3552 bytes left [ 43.986507] warning: process `kudzu' used the deprecated sysctl system call with 1.23. [ 42.019064] bnx2: eth0: using MSI [ 43.161157] bnx2: eth0 NIC SerDes Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON [ 42.383525] Clocksource tsc unstable (delta = -243380491 ns) [ 43.634464] bnx2: eth0 NIC SerDes Link is Down [ 43.664055] bnx2: eth0 NIC SerDes Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON [ 48.343252] warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use) [ 55.807517] VFS: Can't find ext3 filesystem on dev cciss/c0d0p4. [ 56.099222] SysRq : HELP : loglevel0-8 reBoot Crashdump tErm Full kIll saK showMem Nice powerOff showPc show-all-timers(Q) unRaw Sync showTasks Unmount shoW-blocked-tasks [ 60.903264] ACPI: PCI Interrupt 0000:01:04.2[B] -> Link [LNKX] -> GSI 17 (level, high) -> IRQ 17 [ 88.021458] rport-0:0-18: blocked FC remote port time out: removing rport [ 98.410251] rport-1:0-19: blocked FC remote port time out: removing rport [ 1032.565445] warning: process `scrashme' used the deprecated sysctl system call with [ 3274.434768] JFS: nTxBlock = 8192, nTxLock = 65536 [ 3882.924852] fsx-linux used greatest stack depth: 3440 bytes left [ 3899.398928] SGI XFS with large block/inode numbers, no debug enabled [ 3900.447423] Filesystem "cciss/c0d0p4": Disabling barriers, not supported by the underlying device [ 3900.455703] XFS mounting filesystem cciss/c0d0p4 [ 3900.706337] Ending clean XFS mount for filesystem: cciss/c0d0p4 [ 4048.762703] fsx-linux used greatest stack depth: 2736 bytes left [ 4005.576270] SGI XFS with large block/inode numbers, no debug enabled [ 4274.269050] Filesystem "cciss/c0d0p4": Disabling barriers, not supported by the underlying device [ 4274.276858] XFS mounting filesystem cciss/c0d0p4 [ 4274.507809] Ending clean XFS mount for filesystem: cciss/c0d0p4 [ 4319.583542] SGI XFS with large block/inode numbers, no debug enabled [ 4623.862991] Filesystem "cciss/c0d0p4": Disabling barriers, not supported by the underlying device [ 4623.875127] XFS mounting filesystem cciss/c0d0p4 [ 4624.121955] Ending clean XFS mount for filesystem: cciss/c0d0p4 [ 6157.575332] kjournald starting. Commit interval 5 seconds [ 6720.399425] EXT3 FS on cciss/c0d0p4, internal journal [ 6720.399425] EXT3-fs: mounted filesystem with ordered data mode. [ 6728.446431] kjournald starting. Commit interval 5 seconds [ 7412.209956] EXT3 FS on cciss/c0d0p4, internal journal [ 7412.209956] EXT3-fs: mounted filesystem with writeback data mode. [ 6944.869199] kjournald starting. Commit interval 5 seconds [ 7639.350721] EXT3 FS on cciss/c0d0p4, internal journal [ 7639.350721] EXT3-fs: mounted filesystem with ordered data mode. [ 7162.009646] kjournald starting. Commit interval 5 seconds [ 7868.081160] EXT3 FS on cciss/c0d0p4, internal journal [ 7868.081160] EXT3-fs: mounted filesystem with writeback data mode. [ 7351.597855] kjournald starting. Commit interval 5 seconds [ 8061.513602] EXT3 FS on cciss/c0d0p4, internal journal [ 8061.513608] EXT3-fs: mounted filesystem with ordered data mode. [ 7530.298525] kjournald starting. Commit interval 5 seconds [ 8243.454117] EXT3 FS on cciss/c0d0p4, internal journal [ 8243.454122] EXT3-fs: mounted filesystem with writeback data mode. [ 8408.199822] OCFS2 Node Manager 1.5.0 [ 8408.281354] OCFS2 DLM 1.5.0 [ 8408.357012] OCFS2 1.5.0 [ 8409.430196] JBD: Ignoring recovery information on journal [ 7691.200604] kjournald starting. Commit interval 5 seconds [ 8409.538520] ocfs2: Mounting device (104,4) on (node local, slot 0) with ordered data mode. [ 8734.232741] ocfs2: Unmounting device (104,4) on (node local) [ 8023.239901] OCFS2 1.5.0 [ 8750.387938] JBD: Ignoring recovery information on journal [ 8067.400150] kjournald starting. Commit interval 5 seconds [ 8750.496943] ocfs2: Mounting device (104,4) on (node local, slot 0) with ordered data mode. [ 8943.411189] ocfs2: Unmounting device (104,4) on (node local) [ 8190.204973] OCFS2 1.5.0 [ 8953.589242] JBD: Ignoring recovery information on journal [ 8266.114465] kjournald starting. Commit interval 5 seconds [ 8953.685096] ocfs2: Mounting device (104,4) on (node local, slot 0) with ordered data mode. [ 8965.897361] fsx-linux[20349]: segfault at 3606d13 ip 3a93875330 sp 7fff0f106a88 error 4 in libc-2.5.so[3a93800000+144000] [ 8972.459975] ocfs2: Unmounting device (104,4) on (node local)