[ 63.231000] scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 63.231002] [ 63.231003] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 64.516620] scsi 0:0:5:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.516939] target0:0:5: asynchronous [ 64.517113] scsi0:A:5:0: Tagged Queuing enabled. Depth 32 [ 64.517335] target0:0:5: Beginning Domain Validation [ 64.519665] target0:0:5: wide asynchronous [ 64.521505] target0:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.533724] target0:0:5: Ending Domain Validation [ 64.534939] scsi 0:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.535252] target0:0:6: asynchronous [ 64.535425] scsi0:A:6:0: Tagged Queuing enabled. Depth 32 [ 64.535643] target0:0:6: Beginning Domain Validation [ 64.537966] target0:0:6: wide asynchronous [ 64.539811] target0:0:6: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.553719] target0:0:6: Ending Domain Validation [ 66.608600] ACPI: PCI Interrupt 0000:04:03.1[B] -> GSI 31 (level, low) -> IRQ 31 [ 81.840467] scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 81.840469] [ 81.840470] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 85.693630] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.695478] sda: Write Protect is off [ 85.696797] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.697373] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.699216] sda: Write Protect is off [ 85.700539] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.700850] sda: sda1 sda2 sda3 sda4 < sda5 > [ 85.710819] sd 0:0:5:0: Attached scsi disk sda [ 85.711291] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.713136] sdb: Write Protect is off [ 85.714456] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.715046] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.716914] sdb: Write Protect is off [ 85.718249] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.718567] sdb: sdb1 [ 85.719068] sd 0:0:6:0: Attached scsi disk sdb [ 85.719358] sd 0:0:5:0: Attached scsi generic sg0 type 0 [ 85.719591] sd 0:0:6:0: Attached scsi generic sg1 type 0 [ 85.719857] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 [ 85.720221] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 85.720471] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 85.720815] ehci_hcd 0000:00:1d.7: debug port 1 [ 85.721001] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfdc00 [ 85.725057] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 85.725536] usb usb1: configuration #1 chosen from 1 choice [ 85.725769] hub 1-0:1.0: USB hub found [ 85.725946] hub 1-0:1.0: 8 ports detected [ 85.830407] USB Universal Host Controller Interface driver v3.0 [ 85.830653] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 85.831014] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 85.831246] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 85.831579] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e800 [ 85.831927] usb usb2: configuration #1 chosen from 1 choice [ 85.832152] hub 2-0:1.0: USB hub found [ 85.832333] hub 2-0:1.0: 2 ports detected [ 85.938276] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 85.938630] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 85.938859] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 85.939187] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880 [ 85.939532] usb usb3: configuration #1 chosen from 1 choice [ 85.939756] hub 3-0:1.0: USB hub found [ 85.939932] hub 3-0:1.0: 2 ports detected [ 86.046215] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 86.046566] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 86.046804] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 86.047131] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00 [ 86.047477] usb usb4: configuration #1 chosen from 1 choice [ 86.047711] hub 4-0:1.0: USB hub found [ 86.047893] hub 4-0:1.0: 2 ports detected [ 86.154200] usbcore: registered new interface driver libusual [ 86.154417] usbcore: registered new interface driver hiddev [ 86.154630] usbcore: registered new interface driver usbhid [ 86.154801] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 86.155080] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 86.158278] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 86.158457] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 86.158820] mice: PS/2 mouse device common for all mice [ 86.179259] input: AT Translated Set 2 keyboard as /class/input/input2 [ 86.185470] input: PC Speaker as /class/input/input3 [ 87.003924] input: PS/2 Generic Mouse as /class/input/input4 [ 87.007608] i2c /dev entries driver [ 87.007966] IPv4 over IPv4 tunneling driver [ 87.008239] GRE over IPv4 tunneling driver [ 87.008541] TCP cubic registered [ 87.008728] NET: Registered protocol family 1 [ 87.008905] NET: Registered protocol family 17 [ 87.009088] NET: Registered protocol family 15 [ 87.009311] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 87.009490] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 87.009986] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found [ 87.011640] kjournald starting. Commit interval 5 seconds [ 87.011661] EXT3-fs: mounted filesystem with ordered data mode. [ 87.012030] VFS: Mounted root (ext3 filesystem) readonly. [ 87.012248] Freeing unused kernel memory: 224k freed [ 87.012578] Write protecting the kernel read-only data: 1350k [ 87.958354] EXT3 (no)acl options not supported [ 88.109059] EXT3 (no)acl options not supported [ 88.109656] EXT3 FS on sda5, internal journal [ 89.897520] loop: loaded (max 8 devices) [ 89.901772] EXT3 (no)acl options not supported [ 89.902472] kjournald starting. Commit interval 5 seconds [ 89.902670] EXT3 FS on sda1, internal journal [ 89.902900] EXT3-fs: mounted filesystem with ordered data mode. [ 89.912852] EXT3 (no)acl options not supported [ 89.913712] kjournald starting. Commit interval 5 seconds [ 89.918396] EXT3 FS on sda3, internal journal [ 89.918615] EXT3-fs: mounted filesystem with ordered data mode. [ 92.188448] Adding 4192956k swap on /dev/sda2. Priority:-1 extents:1 across:4192956k [ 63.414685] scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 63.414687] [ 63.414688] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 64.700336] scsi 0:0:5:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.700661] target0:0:5: asynchronous [ 64.700834] scsi0:A:5:0: Tagged Queuing enabled. Depth 32 [ 64.701051] target0:0:5: Beginning Domain Validation [ 64.703382] target0:0:5: wide asynchronous [ 64.705221] target0:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.717382] target0:0:5: Ending Domain Validation [ 64.718585] scsi 0:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.718898] target0:0:6: asynchronous [ 64.719071] scsi0:A:6:0: Tagged Queuing enabled. Depth 32 [ 64.719291] target0:0:6: Beginning Domain Validation [ 64.721635] target0:0:6: wide asynchronous [ 64.723473] target0:0:6: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.737368] target0:0:6: Ending Domain Validation [ 66.792282] ACPI: PCI Interrupt 0000:04:03.1[B] -> GSI 31 (level, low) -> IRQ 31 [ 82.024141] scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 82.024143] [ 82.024145] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 85.877292] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.879147] sda: Write Protect is off [ 85.880471] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.881048] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.882937] sda: Write Protect is off [ 85.884256] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.884560] sda: sda1 sda2 sda3 sda4 < sda5 > [ 85.892898] sd 0:0:5:0: Attached scsi disk sda [ 85.893374] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.895224] sdb: Write Protect is off [ 85.896564] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.897148] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.898990] sdb: Write Protect is off [ 85.900304] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.900616] sdb: sdb1 [ 85.901145] sd 0:0:6:0: Attached scsi disk sdb [ 85.901427] sd 0:0:5:0: Attached scsi generic sg0 type 0 [ 85.901652] sd 0:0:6:0: Attached scsi generic sg1 type 0 [ 85.901918] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 [ 85.902287] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 85.902543] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 85.902890] ehci_hcd 0000:00:1d.7: debug port 1 [ 85.903077] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfdc00 [ 85.907144] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 85.907614] usb usb1: configuration #1 chosen from 1 choice [ 85.907842] hub 1-0:1.0: USB hub found [ 85.908024] hub 1-0:1.0: 8 ports detected [ 86.014081] USB Universal Host Controller Interface driver v3.0 [ 86.014323] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 86.014683] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 86.014916] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 86.015250] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e800 [ 86.015601] usb usb2: configuration #1 chosen from 1 choice [ 86.015833] hub 2-0:1.0: USB hub found [ 86.016014] hub 2-0:1.0: 2 ports detected [ 86.121956] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 86.122314] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 86.122545] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 86.122875] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880 [ 86.123219] usb usb3: configuration #1 chosen from 1 choice [ 86.123445] hub 3-0:1.0: USB hub found [ 86.123624] hub 3-0:1.0: 2 ports detected [ 86.229895] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 86.230246] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 86.230479] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 86.230804] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00 [ 86.231147] usb usb4: configuration #1 chosen from 1 choice [ 86.231373] hub 4-0:1.0: USB hub found [ 86.231550] hub 4-0:1.0: 2 ports detected [ 86.337886] usbcore: registered new interface driver libusual [ 86.338108] usbcore: registered new interface driver hiddev [ 86.338322] usbcore: registered new interface driver usbhid [ 86.338499] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 86.338789] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 86.342000] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 86.342183] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 86.342554] mice: PS/2 mouse device common for all mice [ 86.362641] input: AT Translated Set 2 keyboard as /class/input/input2 [ 86.368582] input: PC Speaker as /class/input/input3 [ 87.187056] input: PS/2 Generic Mouse as /class/input/input4 [ 87.190737] i2c /dev entries driver [ 87.191093] IPv4 over IPv4 tunneling driver [ 87.191375] GRE over IPv4 tunneling driver [ 87.191680] TCP cubic registered [ 87.191867] NET: Registered protocol family 1 [ 87.192045] NET: Registered protocol family 17 [ 87.192226] NET: Registered protocol family 15 [ 87.192452] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 87.192627] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 87.193127] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found [ 87.197706] kjournald starting. Commit interval 5 seconds [ 87.197723] EXT3-fs: mounted filesystem with ordered data mode. [ 87.197791] VFS: Mounted root (ext3 filesystem) readonly. [ 87.197835] Freeing unused kernel memory: 224k freed [ 87.198034] Write protecting the kernel read-only data: 1350k [ 88.128190] EXT3 (no)acl options not supported [ 88.267152] EXT3 (no)acl options not supported [ 88.267748] EXT3 FS on sda5, internal journal [ 90.017760] loop: loaded (max 8 devices) [ 90.023151] EXT3 (no)acl options not supported [ 90.024554] kjournald starting. Commit interval 5 seconds [ 90.024797] EXT3 FS on sda1, internal journal [ 90.025013] EXT3-fs: mounted filesystem with ordered data mode. [ 90.035063] EXT3 (no)acl options not supported [ 90.035953] kjournald starting. Commit interval 5 seconds [ 90.040580] EXT3 FS on sda3, internal journal [ 90.040797] EXT3-fs: mounted filesystem with ordered data mode. [ 92.380881] Adding 4192956k swap on /dev/sda2. Priority:-1 extents:1 across:4192956k [ 63.378266] scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 63.378267] [ 63.378268] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 64.663886] scsi 0:0:5:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.664209] target0:0:5: asynchronous [ 64.664381] scsi0:A:5:0: Tagged Queuing enabled. Depth 32 [ 64.664596] target0:0:5: Beginning Domain Validation [ 64.666937] target0:0:5: wide asynchronous [ 64.668785] target0:0:5: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.680966] target0:0:5: Ending Domain Validation [ 64.682166] scsi 0:0:6:0: Direct-Access MAXTOR ATLAS10K4_73WLS DFV0 PQ: 0 ANSI: 3 [ 64.682487] target0:0:6: asynchronous [ 64.682662] scsi0:A:6:0: Tagged Queuing enabled. Depth 32 [ 64.682877] target0:0:6: Beginning Domain Validation [ 64.685201] target0:0:6: wide asynchronous [ 64.687046] target0:0:6: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS (6.25 ns, offset 127) [ 64.700975] target0:0:6: Ending Domain Validation [ 66.755855] ACPI: PCI Interrupt 0000:04:03.1[B] -> GSI 31 (level, low) -> IRQ 31 [ 81.987724] scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 [ 81.987726] [ 81.987727] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs [ 85.840938] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.842789] sda: Write Protect is off [ 85.844111] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.844693] SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB) [ 85.846561] sda: Write Protect is off [ 85.847902] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.848217] sda: sda1 sda2 sda3 sda4 < sda5 > [ 85.858264] sd 0:0:5:0: Attached scsi disk sda [ 85.858721] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.860571] sdb: Write Protect is off [ 85.861889] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.862484] SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB) [ 85.864349] sdb: Write Protect is off [ 85.865671] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA [ 85.865983] sdb: sdb1 [ 85.866496] sd 0:0:6:0: Attached scsi disk sdb [ 85.866797] sd 0:0:5:0: Attached scsi generic sg0 type 0 [ 85.867023] sd 0:0:6:0: Attached scsi generic sg1 type 0 [ 85.867290] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 [ 85.867657] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 85.867910] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 85.868251] ehci_hcd 0000:00:1d.7: debug port 1 [ 85.868439] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebfdc00 [ 85.872505] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 85.872991] usb usb1: configuration #1 chosen from 1 choice [ 85.873220] hub 1-0:1.0: USB hub found [ 85.873404] hub 1-0:1.0: 8 ports detected [ 85.977677] USB Universal Host Controller Interface driver v3.0 [ 85.977922] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 85.978278] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 85.978515] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 85.978847] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e800 [ 85.979193] usb usb2: configuration #1 chosen from 1 choice [ 85.979422] hub 2-0:1.0: USB hub found [ 85.979603] hub 2-0:1.0: 2 ports detected [ 86.085539] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 [ 86.085896] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 86.086125] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 86.086453] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e880 [ 86.086799] usb usb3: configuration #1 chosen from 1 choice [ 86.087027] hub 3-0:1.0: USB hub found [ 86.087210] hub 3-0:1.0: 2 ports detected [ 86.193472] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 86.193826] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 86.194059] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 86.194385] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00 [ 86.194724] usb usb4: configuration #1 chosen from 1 choice [ 86.194951] hub 4-0:1.0: USB hub found [ 86.195128] hub 4-0:1.0: 2 ports detected [ 86.301468] usbcore: registered new interface driver libusual [ 86.301690] usbcore: registered new interface driver hiddev [ 86.301906] usbcore: registered new interface driver usbhid [ 86.302083] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 86.302374] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 86.305529] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 86.305711] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 86.306059] mice: PS/2 mouse device common for all mice [ 86.326113] input: AT Translated Set 2 keyboard as /class/input/input2 [ 86.332292] input: PC Speaker as /class/input/input3 [ 87.155559] input: PS/2 Generic Mouse as /class/input/input4 [ 87.159241] i2c /dev entries driver [ 87.159613] IPv4 over IPv4 tunneling driver [ 87.159886] GRE over IPv4 tunneling driver [ 87.160183] TCP cubic registered [ 87.160367] NET: Registered protocol family 1 [ 87.160540] NET: Registered protocol family 17 [ 87.160712] NET: Registered protocol family 15 [ 87.160935] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 87.161110] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 87.161609] BIOS EDD facility v0.16 2004-Jun-25, 2 devices found [ 87.163255] kjournald starting. Commit interval 5 seconds [ 87.163271] EXT3-fs: mounted filesystem with ordered data mode. [ 87.163338] VFS: Mounted root (ext3 filesystem) readonly. [ 87.163384] Freeing unused kernel memory: 224k freed [ 87.163588] Write protecting the kernel read-only data: 1350k [ 88.094666] EXT3 (no)acl options not supported [ 88.226199] EXT3 (no)acl options not supported [ 88.226799] EXT3 FS on sda5, internal journal [ 89.895426] loop: loaded (max 8 devices) [ 89.899581] EXT3 (no)acl options not supported [ 89.900288] kjournald starting. Commit interval 5 seconds [ 89.900501] EXT3 FS on sda1, internal journal [ 89.900727] EXT3-fs: mounted filesystem with ordered data mode. [ 89.910631] EXT3 (no)acl options not supported [ 89.911507] kjournald starting. Commit interval 5 seconds [ 89.916182] EXT3 FS on sda3, internal journal [ 89.916399] EXT3-fs: mounted filesystem with ordered data mode. [ 92.161310] Adding 4192956k swap on /dev/sda2. Priority:-1 extents:1 across:4192956k